To use a floor jack safely, park on hard, level ground, chock the wheels that stay on the ground, lift at the jack point your owner’s manual shows, and then set jack stands under the car before you do any work. A jack is for lifting only. It should never be the thing holding the car up while you’re underneath.
That last rule is the one that matters most, so keep it in mind as we go step by step.
What you need before you start
Gather your gear first so you’re not tempted to cut corners halfway through.
- A floor jack rated for more than your vehicle’s weight.
- A pair of jack stands (or more) rated for your vehicle’s weight, and never used beyond their rating.
- Wheel chocks.
- Your owner’s manual.
- Work gloves and safety glasses.
Pick the right spot
Where you lift is as important as how. Choose a flat, hard surface like a concrete garage floor or a level paved driveway. Soft ground, grass, slopes and asphalt on a hot day can all let a jack sink or slip.
Put the car in park (or in gear for a manual), set the parking brake, and place chocks snugly against the tires that will stay on the ground. If you’re lifting the front, chock the rear wheels, and the other way around.
Find the correct jack points
Your owner’s manual shows exactly where the lift points are on your car. They’re usually reinforced spots along the pinch weld just behind the front wheels and ahead of the rear wheels, or specific spots on the frame or front and rear crossmembers.
Don’t guess. Lifting on thin body panels, the oil pan, or suspension parts that aren’t meant to carry weight can damage the car and let it shift. Some vehicles have a central point for lifting one whole end, which makes things easier.
Lift the car step by step
- Position the jack saddle directly under the lift point, with the jack square and not at an angle.
- Pump the handle slowly, watching the saddle and the car as it rises. If anything shifts, lower it and reset.
- Raise the car just high enough to slide the stands in, with a little room to spare.
- Place a jack stand beside the jack, under a solid support point listed in your manual, and make sure it’s locked. The stand should sit on the same flat, hard surface as the jack.
- Slowly lower the car onto the stand until the weight transfers. Keep the jack in place, just barely touching, as a backup.
- Give the car a firm push at a corner to check that it’s steady. If it wobbles, lower it and start over.
For a quick breakdown of what to buy, our guide to the best floor jacks 3 ton low profile explains what to look for, and the low profile 3-ton floor jacks list is handy for sports cars and sedans.
Never go under a car held only by a jack
Hydraulic jacks can leak down or fail without warning, and a car that falls can seriously hurt or kill you. Jack stands have mechanical locks and are built to hold weight steadily. So, no matter how quick the job is, don’t put any part of your body under the car until stands are in place.
Also, never use bricks, cinder blocks or wood stacks as stands. They can crack or slip under load.
Lowering the car
When you’re done, make sure you, your tools and your parts are all clear of the car. Raise the car slightly to take weight off the stands, remove them, then lower the car slowly by opening the release valve gently. Pull the chocks last.
If your garage is cramped, our roundup of the best floor jacks for small spaces may help, and our air compressor size guide is a good companion for the garage.
Common mistakes to avoid
Most jack accidents come from a short list of mistakes, and they’re all avoidable.
- Skipping the stands because the job is quick.
- Lifting on soft or sloped ground.
- Using the wrong lift point, or a spot that bends under load.
- Forgetting to chock the wheels that stay down.
- Using a jack or stand rated below the car’s weight.
- Starting the engine or rocking the car while it’s up.
Also, check your gear now and then. Look for leaking fluid, bent parts or cracked welds, and replace anything damaged. A car-lifting tool that looks questionable isn’t worth the risk.
Frequently asked questions
Where do I put the floor jack?
Use the lift points shown in your owner’s manual. They’re reinforced spots designed to carry the car’s weight.
How many jack stands do I need?
At least two for one end of the car, placed on matching sides. Some people use four to raise the whole vehicle, but only if the surface is level and the manual allows it.
Can I use a floor jack on a slope?
No. A sloped surface can make the car roll or the jack tilt. Move to flat, hard ground.
The bottom line
Learning how to use a floor jack safely comes down to a few habits: level ground, chocks, the right lift points and jack stands every time. Take an extra minute for each, and you’ll lift a car with confidence.

