To fix sewing machine tension problems, first rethread the upper thread with the presser foot raised, then check the bobbin and needle. Sew a test seam on matching scrap before making a small upper-tension change. Loose loops often come from threading, while puckers may also come from fabric or stitch setup.
That quick check can save you from turning dials without knowing what’s wrong. If the stitches still look uneven, make one small adjustment at a time and test again; there’s no single tension number that works for every thread, fabric, and stitch.
What sewing machine tension does
Tension controls how the upper thread and bobbin thread meet inside the fabric. Ideally, they interlock between the fabric’s layers, leaving neat stitches on both sides. If one thread pulls too strongly, the join can shift toward the top or bottom.
Your machine’s upper-thread tension dial controls how freely the thread moves through the tension system. Bobbin tension is usually set separately, but it’s best not to change it as a first step. Many sewing machine tension problems come from threading or setup, not a bobbin setting that needs turning.
So, look at both sides of the seam before changing anything. The side where the stitches look wrong can offer a clue, but it won’t always point to one cause on its own.
How to diagnose sewing machine tension problems
Loops on the underside often mean the upper thread isn’t seated in the tension system or is too loose. With the presser foot raised, the tension discs open so the thread can sit between them. If you thread the machine with the foot down, the thread may not enter the discs properly.
On the other hand, loops on top can point to an upper thread that’s too tight, or to a bobbin that isn’t threaded correctly. Puckering may also mean the upper tension is too high, but thin fabric, an unsuitable needle, or a stitch that’s too long can cause trouble too.
Rather than judging from a single stitch, look closely at a few inches of sewing on both sides. If loops or puckers show up only with one fabric or thread, the material and setup may be part of the problem.
What to check before adjusting tension
Start with the basic setup, then test again. Turn off the machine before handling the needle or rethreading, and follow your manual if the threading path isn’t clear.
- Raise the presser foot and needle, then rethread the upper thread from the start. Make sure it follows every guide and sits in the tension discs.
- Remove and reinsert the bobbin as your manual shows. Check that the thread unwinds in the right direction and passes through the bobbin case’s guide or slot.
- Check that the bobbin is wound evenly and isn’t damaged. If you’ve changed thread, confirm it’s suitable for your machine.
- Look at the needle. Replace it if it’s bent, blunt, or damaged, and check that it’s inserted in the correct direction and pushed fully into place.
- Clear lint from the accessible bobbin area as your manual allows. Don’t force or take apart parts you’re unsure how to handle.
Once you’ve checked those points, stitch a test seam before changing a dial. Rethreading can make a big difference, so for a closer look at the thread path, see our guide on how to thread a sewing machine. With the setup sorted, you’ll have a better sense of whether tension is the real issue.
How to adjust sewing machine tension safely
Use a scrap with the same number of fabric layers as your project, and sew with the same thread and stitch settings. If the upper thread is clearly too loose, increase the upper tension a little; if it’s too tight, decrease it a little. Make just one small change at a time.
After each change, sew another test seam and check both sides. If the stitches improve, keep testing until they look balanced. If they get worse, return to the previous setting before trying another small adjustment.
Here’s the catch with bobbin tension: don’t turn the bobbin screw unless your manual calls for it and you know how to restore its setting. A small change can have a big effect, and the correct adjustment varies by machine. If rethreading and careful upper-tension tests don’t help, ask a qualified sewing machine technician to inspect it.
When the problem may not be tension
Uneven stitches can have more than one cause, so a tension dial isn’t always the answer. Skipped stitches, for example, can point to a needle that doesn’t suit the fabric or isn’t installed properly. Our guide to fixing skipped stitches can help you check those possibilities.
Fabric can also feed unevenly if you pull or push it while sewing. Let the feed dogs move it through the machine, and check that the presser foot is down. If you sew a range of materials and want to compare machine features, our guides to adjustable computerized sewing machines, computerized machines for professional sewing, and smart computerized sewing machines cover options to explore.
Frequently asked questions
Why are there loops under my fabric?
Loops underneath often mean the upper thread isn’t seated between the tension discs, or its tension is too loose. Raise the presser foot and rethread from the beginning before adjusting the dial.
Should I adjust bobbin tension to fix loose stitches?
Usually, start by checking the upper thread and making sure the bobbin is inserted and threaded correctly. Adjust bobbin tension only if your manual recommends it or a technician advises you to.
Why does my sewing machine pucker the fabric?
High thread tension can pull fabric into puckers, but the needle, stitch length, and fabric can also play a part. Test on a matching scrap and change one setting at a time.
The bottom line on sewing machine tension
Sewing machine tension problems are often easier to solve once you’ve checked threading, bobbin placement, and the needle. Test on matching fabric, make small upper-tension changes, and avoid adjusting the bobbin without a clear reason. If you’re considering a different machine, the linked buying guides can help you compare features for your kind of sewing.

